Ground Glue Tech-Tonic Rock, Mulch, Sand and Gravel Binder

Ground Glue® Tech-Tonic Rock, Mulch, Sand and Gravel Binder is a concentrated and powerful landscaping glue for keeping gravel, pebbles, pea gravel, DG, mulch, wood chips, bark, shells, sand, pine needles, straw, hay and similar landscape surfaces locked in place where you want them. Ground Glue Tech-Tonic keeps your landscaping materials locked in place, so your yard, landscaped beds, paths and trails look great – even after wind and rain – while still allowing rain and water to pass through to irrigate your plants, soil and foundation. Ideal for use on pathways, trails, borders, slopes and flower beds.

• Reduces erosion
• Stabilizes paths and trails, and increases the load bearing of surfaces
• Blow leaves out of flower beds without disturbing the landscape mulch, sand or gravel
• PET SAFE formula is safe for all animals and plants (rinse overspray from foliage)
• Weatherproof to withstand intense rain, hail and sleet, so that your landscaping materials stay put
• Economical & long-lasting: Properly applied, Ground Glue Tech-Tonic can last for a full year or more
• Penetrating formula – prewetting not required
• Works on all soil types
• Made in the USA

DIRECTIONS / COVERAGE

General: Multiple applications provide greater effect. Ensure application and mixing equipment is thoroughly washed immediately after application. Sprayers should be thoroughly flushed with hot water and soap after application. Allow surfaces to dry before reintroducing traffic. Allow 24-hours to cure before load or water (including rainfall) are applied to the treated surfaces. Remove excess product (e.g. overspray areas) by rinsing with water prior to the product drying. Likewise, thoroughly flush with water any foliage which may have accidentally been oversprayed with Ground Glue Tech-Tonic.

Good: Apply single treatment topically with a sprayer or watering can. Apply until treatment begins to pool on surface of substrate.

Better: Apply up to three treatments as above. Allow surfaces to dry before reapplication (approximately 1 hour between each).

Best: Treat gravel, sand, soil or mulch substrates prior to installation. Using a shovel, trowel or similar device, mix clean and dry substrate with a single treatment of Ground Glue Tech-Tonic in a container such as a wheelbarrow, drum or bucket(s). After thorough mixing, shovel, dump, and the level treated substrate onto the intended. This method will yield the greatest coverage and effectiveness.

AGGREGATE CONTROL DIRECTIONS (90 ft²/gallon per application)

Aggregate includes limestone gravel, pea gravel, decomposed granite (DG), recycled concrete aggregates and other similar fragmented rock or mineral surfaces.

1. For better results, scarify aggregate 1-2” deep.

2. Dilute Ground Glue Tech-Tonic 1 part product concentrate with 4 parts water.

3. Spread ½ gallon of diluted product per one square yard.

4. Compaction is optional, but rolling or compacting scarified surface will result in greater longevity

SAND CONTROL DIRECTIONS (54 ft²/gallon per application)

1. Dilute Ground Glue Tech-Tonic 1 part product concentrate with 2 parts water.

2. Spread ½ gallon of diluted product per one square yard.

3. Apply slowly and wet-through only 2” of sand. For treating greater depths of sand, wait one hour and reapply.

4. Compaction is optional, but rolling or compacting sand will result in greater longevity.

MULCH CONTROL DIRECTIONS (54 ft²/gallon per application)

Mulch includes wood mulch, straw, sawdust, pine needles & cones, and nutshell based substrate.

1. For better results, rake/rough the mulch surface to about 1” depth.

2. Dilute Ground Glue Tech-Tonic 1 part product concentrate with 2 parts water.

3. Spread ½ gallon of diluted product per one square yard.

4. Wet-through entire mulch layer.

5. Ensure mulch is wiped from surfaces prior to drying.